Skip to content
Alpharetta Cabinet Studio

Cabinet Refacing in Alpharetta, GA

Cabinet refacing in Alpharetta covers the doors and the fronts without touching the countertop or the plumbing underneath.

Get my free estimate >>

Free estimate from a local cabinet pro. No obligation.

Get my free estimate

Free estimate from a local cabinet pro. No obligation.

By submitting you agree to be contacted about your project.

Or call (678) 606-5523. Calls only, we do not receive text messages.

Call (678) 606-5523

Answered 24/7

A 1990s kitchen built with quality boxes often has another decade in its structure, and cabinet refacing in Alpharetta, GA is the path that preserves that investment. Alpharetta Cabinet Studio evaluates the existing frames first: if the plywood is dry and the cases are square, refacing replaces every visible surface while the bones stay in the wall. The question owners of an upscale 1990s kitchen ask most often is whether refacing can deliver the modern look they want, and the honest answer depends on which look they have in mind.

  • Free estimate from a local pro
  • No obligation to go ahead
  • Semi-custom to full custom
Kitchen mid-refacing with all doors removed from the upper and base boxes and new doors leaning against the wall.

About our cabinet refacing

One answer surprises most owners: a shaker or slab door in a painted finish is fully achievable through refacing, but an inset look is not. Inset doors require a face frame built to the door opening, so the geometry of the existing boxes cannot support them. A different renovation scope, a full replacement, is what produces that inset result. Call to schedule a consultation and find out which path fits the look and the budget.

Cabinet refacing in Alpharetta

Cabinet refacing in Alpharetta for framed and frameless boxes

Refacing works differently on a framed cabinet than on a frameless one. On a framed cabinet, the new veneer or thermofoil goes over the existing face frame, and the new doors hang from the existing frame. On a frameless cabinet, the process involves applying a new face frame over the box ends, which changes the interior opening slightly. Both are legitimate paths, but the installer needs to know which box type they are working on before the material is ordered.

  • A refacing quote that does not state the box type may be priced for the easier method and repriced at installation when the actual boxes are different.
  • Frameless boxes refaced with a face frame produce a slightly smaller door opening than the original. That matters for deep drawers.
  • So you know what the refacing will produce before the job starts, not when the installer is standing in the kitchen.
Get my free estimate >>

Free estimate from a local cabinet pro. No obligation.

Call (678) 606-5523

Answered 24/7

Box condition check for refacing in Alpharetta

Check the sink run before you commit to a cabinet reface

The box condition check for a refacing job in Alpharetta has three points: the bottom shelf near the sink and dishwasher for moisture damage, the corner joints for racking, and the drawer slides for looseness. A plywood box that passes all three is a good reface candidate. One that fails any is a candidate for replacement, even if the rest of the kitchen refaces cleanly. Ask about box condition at the estimate, because the answer changes the scope.

  • Swollen particle board at the lower run near the sink is the most common refacing deal-breaker in kitchens over fifteen years old.
  • A racked case that is out of square produces a door that will not hang level after refacing, regardless of the hinge adjustment.
  • So you get a refacing quote that covers the boxes worth keeping and replacement quotes only where the boxes have failed.
Get my free estimate >>

Free estimate from a local cabinet pro. No obligation.

Call (678) 606-5523

Answered 24/7

Cabinet refacing without countertop disruption

Refacing without touching the countertop or the plumbing

The reason most Alpharetta homeowners choose refacing over replacement is the countertop: a refacing job leaves the existing countertop, sink and plumbing in place, so the kitchen is out of service for days, not weeks. That is legitimate when the boxes are sound and the countertop is worth keeping. But a refacing job on boxes that need replacement, done to avoid touching the countertop, produces a kitchen that will need to be redone sooner. The box condition, not the desire to keep the countertop, should drive the decision.

  • A countertop that does not need to be replaced is a reason to reface if the boxes are sound. It is not a reason to reface if they are not.
  • How long without a kitchen? A refacing job typically takes three to five days. A full replacement takes longer because the countertop fabrication adds a separate lead time.
  • So you choose based on what the boxes need, not on what keeps the kitchen usable the longest.
Get my free estimate >>

Free estimate from a local cabinet pro. No obligation.

Call (678) 606-5523

Answered 24/7

Why Alpharetta Cabinet Studio

How to plan your project

Tell us about the room and a local cabinet pro gives you a free estimate, with no obligation to go ahead.

FreeAn estimate from a local cabinet pro, with no obligation
Line by lineAsk for every cabinet to be listed in the estimate, so changes stay simple
4 to 16 wksTypical lead time, semi-custom to custom; ask for yours at the estimate
LevelledBoxes shimmed, scribed and checked before the doors go on
Get my free estimate >>

Free estimate from a local cabinet pro. No obligation.

Call (678) 606-5523

Answered 24/7

Why inset is not a refacing option

Every 1990s kitchen was built as either a framed or frameless box, and nearly all of them use an overlay door: the door closes over the face frame rather than inside it. Refacing that kitchen means applying new veneer or rigid thermofoil to the face frames and hanging new doors on those same frames. The doors change. The geometry does not.

Inset doors work on a different principle. The door sits flush inside the face frame opening, with a small, even reveal all the way around. That reveal is not a hinge adjustment. It is the result of the face frame being built to the door, with the opening sized to the door from the start. An existing overlay face frame was built to a different tolerance, and no shimming or adjustment creates a consistent inset reveal from it.

The practical result is that an inset look requires new boxes with face frames sized from scratch, not veneer over the existing ones. Frameless boxes carry the same limitation: the hinge hole pattern and the door-to-opening proportion were set for an overlay door, not an inset one. If the goal is a fitted, flush inset look, the conversation shifts from refacing to a full replacement. Refacing is the right scope for owners who want a shaker, slab or raised panel door in a new finish on the existing layout, without the cost and lead time that new boxes carry.

Changing the upper run without new boxes

The wall cabinets above the countertop offer more flexibility during a refacing project than most owners expect. The box positions stay fixed, but what goes on the front of those boxes can change the character of the whole upper run.

Glass inserts replace a solid panel on any upper door where the frame is structurally sound. A door frame with tempered glass in the center lets the upper run read lighter and open, and multiple glass doors in the same run create a continuous visual break from the solid material below. The glass is specified at the door order stage so the opening sizes are part of the fabrication, not an afterthought.

Open shelving is a second option. Removing the door from one section of upper cabinet leaves the box in place and finishes the front edge with a wood strip or a new face frame piece that reads as a shelf ledge. One or two open sections in a longer upper run shifts the feel of the space from enclosed storage to a mix of display and storage, without touching the layout or the countertop.

Crown molding at the top of the upper run and a light rail along the bottom are both within the refacing scope. A new crown profile can simplify a dated ornate run or add height to a flat one. A light rail positions the trim for under-cabinet lighting so the wiring can be routed before the trim is set, rather than cut in afterward.

White shaker cabinets with black pulls, a grey quartz-topped island, subway tile and a window above the sink.

New drawers inside old boxes

Drawer fronts are replaced as part of any refacing job because the face of the drawer is a veneer surface the same as the doors. The drawer box itself, the interior wood component that slides in and out carrying the load, can also be replaced during the same project.

A 1990s drawer box was often built from stapled plywood with center-mount slides that limit travel to roughly 75 percent of the drawer depth. The drawer opens, but the back section stays inside the box, unreachable without pulling the drawer out and reaching past the front. This is a functional limit that has nothing to do with the door style or the finish.

New drawer boxes in dovetail construction, paired with full-extension undermount slides, fit into the existing box opening during the same refacing project. The opening governs the new drawer box dimensions, and the undermount slides mount to the floor of the box interior. When the job is done, the drawer travels the full depth of the box and the hardware is invisible from the front.

Soft-close motion is standard in current undermount slide systems: the drawer decelerates and closes quietly without a separate mechanism. A large kitchen with ten or twelve drawer bases can have all of them updated in the same scope as the refacing work, without removing or replacing a single box from the wall.

Refacing cost on a large kitchen

Cabinet refacing in Alpharetta typically runs roughly $4,500 to $10,500 as an estimated range for a full kitchen. The largest variable is door and drawer front count: a 1990s custom kitchen often has more specialty storage units and more total doors than a builder-grade kitchen of the same footprint, so the material and labor scope is larger than square footage alone suggests.

Door style is the second cost driver within the refacing scope. A slab door is the simplest mill cut. A shaker adds a profile step. A raised panel adds another. The estimated difference between a slab and a raised panel can run roughly $20 to $60 per door in the same material, and a 20-door kitchen registers that difference in the total quote.

Glass inserts, open shelving conversions and new drawer boxes with full-extension undermount slides are each a separate line item. Glass adds a cost per door for the routed opening and the tempered insert. A drawer box replacement with undermount slides adds a per-drawer unit cost. These additions are itemized in the written scope so the owner decides which to include before the order is placed.

For owners weighing the two scopes: a semi-custom kitchen replacement runs roughly $150 to $700 per linear foot installed, and a custom replacement runs roughly $500 to $1,200 per linear foot, putting a full custom kitchen in the roughly $10,000 to $60,000 estimated range. Refacing makes sense when the boxes are sound and the layout stays put; replacement is the scope when the layout changes or the boxes have failed.

Every refacing figure on this page is an estimated range; the written scope sets the final price once the boxes, door count and material are confirmed.

The same kitchen, refaced

Dated L-shaped kitchen with honey oak arch-top cabinets, laminate counters, white appliances and a recessed fluorescent ceiling light.The same L-shaped kitchen with white doors and drawer fronts on the original boxes, almond counters and white appliances unchanged.BeforeAfter
New doors and drawer fronts on the original boxes; the layout is unchanged.

The process

From first call to installed cabinets

Four steps, and you make a decision at the end of each one before the next begins.

  1. Call or send the form

    Tell us about the room and what you want from it, and a local cabinet pro contacts you to talk it through.

  2. Free estimate

    A free estimate for the room, with door style, finish and hardware choices to weigh before you commit.

  3. Decide, then order

    Ask for every cabinet and the lead time to be listed in writing. Nothing is ordered until you decide to go ahead.

  4. Delivery and install

    Boxes are checked on arrival, set level and scribed to the walls, doors adjusted, then a walk-through with you.

Get my free estimate >>

Free estimate from a local cabinet pro. No obligation.

Call (678) 606-5523

Answered 24/7

More cabinet options

New apartment kitchen with grey flat-panel slab-door cabinets, white quartz counter, a wall oven, induction cooktop, pull-out faucet and wood-look floor.Corridor of a newly built apartment building with floors papered and an open door showing a white shaker kitchen.White raised-panel base and upper cabinets installed with a plywood subtop, a level and a drill resting on it.

Service area

Areas covered by these guides

Questions

Cabinet Refacing: Common Questions

Can refacing work on frameless boxes as well as framed ones?

Yes. Refacing a frameless box means applying new veneer to the visible exterior surfaces and the edge banding on the interior front edge, then hanging new doors on the existing hinge hole pattern. Frameless construction uses a different hinge system than framed, so the door hardware is specified to match. The limitation on inset doors applies to frameless boxes as well: the opening geometry was set for an overlay door at the factory, and that geometry does not change with a reface.

How do I know whether my existing boxes are worth keeping?

The evaluation covers four things: whether the box sides are plumb and square, whether the plywood or particleboard is free of water damage or delamination, whether the joints are tight, and whether the box is fastened securely to the wall. A box that fails any of these checks is not a refacing candidate because the new surfaces would be applied to a failing structure. Boxes that pass this check typically have another decade or more of useful life ahead of them.

Does refacing disturb the countertop or the plumbing?

Refacing leaves the countertop, sink and plumbing connections in place throughout the project. The work is entirely on the vertical surfaces and the doors. This is one reason a refacing project runs faster than a full replacement: the countertop template step is not part of the sequence.

What painted finish options are available for refacing?

Painted maple is the most common option: it has a tight grain that takes paint evenly and holds up to the cleaning that kitchen surfaces require. Painted MDF doors are also available at a lower cost per door, though MDF is more vulnerable to moisture at edges and corners over time. Thermofoil in solid colors is a third path, with a shorter lead time than painted wood. The finish choice is confirmed at the consultation stage before any material is ordered.

How long does a refacing project take from start to finish?

Lead time depends on the door fabrication schedule and the material chosen. Thermofoil doors on stock profiles can be ready in roughly two to three weeks from order. Painted wood doors typically run closer to four to six weeks. Installation itself is shorter than a full replacement because no new box construction is involved and the countertop stays in place, so no countertop template or fabrication step is in the schedule.

What does the written warranty cover on a refacing project?

The manufacturer warranty covers the work completed under the project scope; ask for the current terms before placing your order. Ask about the current warranty terms before the order is placed.

Free estimate

Talk to us about cabinet refacing

Tell us about the room, in Alpharetta or anywhere in the service area, and a local cabinet pro gives you a free estimate, with no obligation.

Get my free estimate >>

Free estimate from a local cabinet pro. No obligation.

Call (678) 606-5523

Answered 24/7

Calls only, we do not receive text messages.

Call (678) 606-5523